Sabre-leg chair

Thomas Hope, connoisseur and dilettante, is credited with the original concept of this radical design, but it was George Smith, cabinet-maker and furniture-maker who simplified the neoclassical shape and made the flush-sided chair a practical
Signs ofauthenticity
1. In solid wood, cut across the grain on the side frames so that at no point is the grain running at an angle of more than 45′.
2. Back rail and crest rail tenoned inside back frame supports.
3. Seat frame flowing in continuous line from crest rail to legs.
4. Upholstered seat contained within seat frame, not
overstuffed.
5. Decoration, stringing, brass inlay, flush with surface and silhouette.
6. On chairs with arms, arm supports in counter-curve to front legs, often with scrolling at armrest.
7. Arms follow precise curve of seat and back frame, finishing flush into front of back support.
8. On chairs with arms, upholstered seat contained within seat frame and arms.
9. Front legs with more pronounced forward curve than back curve of back legs.
10. All legs square-sectioned, unstretchered.
Likely restoration and repair
11. Caned seats replaced with upholstery, covering front seat rail.
12. Legs broken, split and
pinned - most vulnerable point just below knees of front legs. Examine grain closely for
repairs.
13. Back supports broken and repaired. Both these points may not detract from appearance but considerably weaken structure.
14. Decorative brass rosettes on sides of knees, seat frame
junction with back legs - may conceal pinning or repair.
15. Attractive if incongruous carving on front legs other than reeding. Probably conceals a partly replaced leg.
commercial proposition. Its lines derive from Ancient Greek and Egyptian rather than the Adam `classical’ and it represented the height of the Regency taste for unbroken lines and severe curves. Probably the most well-known design – certainly the most copied and reproduced – is the `Trafalgar’ chair, with a rope-twist incorporated into the crest rail or back rail, made to commemorate Nelson’s victory.
There had been many technical advances in furni making by the end of the eighteenth century. Steam-driven machinery, bonding, laminating and veneer-cutting , all had a considerable influ on furniture design. There also a far greater scientific understanding of weight and stress. The flush-sided chair remarkably modern construction, with the timbers cut scientifically across the grain so that the leg and side-frame were made in a single piece, bonded to the curving back and back leg in a single continuous line.
Construction and materials
This radical design was made in solid mahogany, rosewood, simulated rosewood, ebonized beech, real and simulated calamander, and, in some less costly versions, with side frames and seat rails of solid dark woods with a beech underframe. The test of a genuine flush-sided chair is that it can be laid completely flat on its side on the floor. Legs are always unstretchered, the front legs frequently have a more pronounced curve than the back legs - hence its name ’sabre leg’. The crest rail, often several inches deep, is tenoned to the inside of the back supports and does not overrun the seat frame. Chairs with flush sides and crest rails over-running the side are of later date. Seats were upholstered and curved with the side-frame. They were never overstuffed at the front, where there was always a straight seat rail joining the two high-curving knees.
In line with the fashions of the day, the sabre-legged chair was also made in a lighter construction, with a dark wood, or ebonized beech for the frame, and caned seat and back panel.
Detail
Frequently there was continuous reeding which carried from the side of the crest rail, down the top of the seat frame, over the knees and down the front of the slightly tapered square-sectioned legs. Brass inlay, stringing and decoration were flush with the surface. On arms, there is often scrolling at the end of the armrest.
Variations
These chairs required a considerable amount of technical knowledge and equipment to make, and consequently there are no country versions of this design.
The simple shape of the traditional slat back with a deep, plain crest rail and plain wooden or rush seat could probably be related to the sabre-legged chair, but it would be stretching the point. The most commonly reproduced design is the over-curving S-armed chair with matching
dining chairs, often with caned seats, and most frequently found in beechwood, ebonized or painted and gilded. Strictly speaking, these are not true flush-sided chairs, since their arms are round-sectioned and their wide crest rails usually overrun the sides.
Below left: flush-framed, c.1830. Right: cane-seated, flush-framed, c.1820. The rope-twist crest rail has been broken by a stylized decorative design.
Reproductions
Victorian
From the beginning of the Victorian period, the pure shape of the flush-sided chair became spoiled by turned front legs instead of the strict curve of the sabre leg. This was probably because the flush-sided chair was by nature expensive to make and used a considerable amount of timber to achieve the right
spring and strength to the legs.
Twentieth century
Few of the myriad variations begin to match the elegance and simplicity of the original. About 30 years ago the lyre back was very much in fashion, and a variation of the flush-sided chair was made commercially by some high-quality manufacturers, usually in ebonized beech. They proved to be far less durable than the originals, mainly because the difficult cross-cutting of the timber was skimped, and the sabre legs split where the grain ran at too acute an angle.
Modern versions of a cane-seated flush-sided chair are to be found in some high-quality department stores, made with modern techniques, probably in High Wycombe, centre of the chair-making industry in
England, where many of the originals were also made.
Price bands
Late Regency, with overrunning crest rail, £120-150 each. Set of six, £800-1,000.
Cane seat, simulated rosewood, beach frame - set of six, £.880-1,000.
S-arm chair, £250-320.
Plain mahogany - set of six, £700-900.
(Rosewood more expensive than mahogany; brass inlay also more expensive.)
William iv turned leg - set of six, £600-850.

Bentwood chairs have become so much a part of our lives as to be almost invisible. In a simplified form they have been used in so many everyday places - shops, schools, private houses and public places - that it is difficult to imagine that their whole style was once a complete revolution in furniture-making. Today they are turned out in their thousands in factories all over
Signs of authenticity
1. Laminated wood, built up of alternately grained strips.
2. Generous curves with long unbroken sections curving under and over, rather than separate pieces joined at short intervals.
3. Taut panels caned on the diagonal to allow for the springiness of the chair.
4. Surface of wood smooth and silky, instantly recognizable once touched, compared with later solid bentwood.
5. Impeccable finish with sections shaped and smoothed to flow into the join.
6. Early solid birch bentwood chairs should be finely sanded and finished under black
I ebonized’ paint.
Likely restoration and repair
7. Laminated bentwood chairs and rockers which have been subject to too many changes in temperature and humidity will be ’sprung’ on curves, i.e. there will be splitting where the wood has shrunk and pulled away. It may be tacked and glued back into position but the damage is permanent and will occur again.
8. Recaned on the horizontal and vertical. The caning will break and the chair will not maintain its shape, but will eventually split from the strain.
9. Black paint stripped off. If this has been done by complete immersion in a caustic solution there may be some dissolving of the adhesives between laminations. Stripping must be done painstakingly by hand and there should be some small signs of remaining paint.
England, but their origins were elite and aesthetic.
Michael Thonet (1796-1871),
their inventor, was an Austrian who trained as a craftsman in the South German Biedermeier school of furniture-making. This was established as a reaction against French influence, in part motivated by the aspiration for a united Germany after the Napoleonic Wars, and in part aesthetic, a search for well-designed ‘bourgeois’ furniture. The parallel desire was felt in England, and was evident in the designs of J. C. Loudon and his school. Biedermeier was particularly successful with seat furniture, which was solid, well-made, elegant and, above all, comfortable. It was Michael Thonet’s search for new materials and techniques to
make chairs without ornament, carving or traditional construction that led him to experiment with the shipbuilding techniques of steaming and bending wood. His designs were first produced in laminated wood in the 1840s.
Thonet took out patents for his chair-making techniques, but when the patent ran out in the 1860s a London firm of furniture-makers, Hewlett and Company, took it up, and by the end of the century bentwood chairs were being made by many furniture-makers, particularly in High Wycombe, centre of England’s chair-making industry.
Construction and materials
Michael Thonet’s original designs were made in thin strips of wood, steamed and bent into shape and laminated together - a technique which had been known in England for about 100 years, although laminated wood had only been used for parts of furniture and not for a whole piece. Thonet’s first commission for these novel, smooth-curving designs was for the Leichtenstein Palace in Vienna, and although they were more detailed and complicated in their sinuous construction, the basic bentwood chair of today differs very little from those prototypes.
In England, the technique of steaming and bending wood had been applied to Windsor chairs for some years, using solid wood as
Variations
Bentwood chairs were particularly suitable for children, and both high chairs and small, miniature versions of the standard shape were made, particularly in the 1920s, for use in schools and nurseries.
Some early, finely designed, bentwood chairs made in England include versions of the sabre-legged S-armed chair, with the back made in a single hoop with the back legs, which are raked well back. Front legs curved forward in imitation of the line of the sabre-leg, but were round-sectioned and taper-turned. The S-curve of the arms was particularly suitable for the new bentwood technique.
Once furniture-making factories had begun to turn out bentwood chairs by the thousand, their finish and style degenerated into the ‘tearoom chairs’ of the 1920s and 1930s, being reduced to circular hoops and slightly splayed legs, whose timber was no longer carefully chosen for the correct grain, and which have since split and cracked.
opposed to laminated. The timber was generally birch, traditional wood for chair-legs because it was amenable to bending and was springy enough not to break or split. The cane seat, too, had been in production for country chairs and lightweight seat furniture ever since Sheraton had reintroduced it at the end of the eighteenth
century.
Early genuine Thonet bentwood chairs and rockers, for which the technique was particularly
suitable, were more curvaceous and elaborate, mainly due to the laminated wood which allowed more freedom than later bentwood chairs in birch, which consisted mainly of a series of hoops and standardized curves.
Reproductions
After a considerable spell of unpopularity as ‘cheap chairs there are now many extremely good reproductions of the original bentwood chair on the market, many of them originating in Taiwan and the Far East, where manufacturing is cheap and labour still skilled in traditional crafts such as caning. Their reappearance on the English scene can largely be attributed to the many well-designed small restaurants with imaginative decor, for which they were originally imported.
Price bands
Superb intricate shapes, top condition with original labels and original, unshipped
finish, £850-1,000.
Stripped or plain, simpler shapes with original label, £550-850.
Set of six chairs, original caning and labels, £350-500.
Period singles with labels and authentication, 135–50.
1920s plain but in good condition, £15-20.
Above: a child’s bentwood high chair, c.1870.
Right: an original Thonet, c.1860.