Sabre-leg chair

Thomas Hope, connoisseur and dilettante, is credited with the original concept of this radical design, but it was George Smith, cabinet-maker and furniture-maker who simplified the neoclassical shape and made the flush-sided chair a practical
Signs ofauthenticity
1. In solid wood, cut across the grain on the side frames so that at no point is the grain running at an angle of more than 45′.
2. Back rail and crest rail tenoned inside back frame supports.
3. Seat frame flowing in continuous line from crest rail to legs.
4. Upholstered seat contained within seat frame, not
overstuffed.
5. Decoration, stringing, brass inlay, flush with surface and silhouette.
6. On chairs with arms, arm supports in counter-curve to front legs, often with scrolling at armrest.
7. Arms follow precise curve of seat and back frame, finishing flush into front of back support.
8. On chairs with arms, upholstered seat contained within seat frame and arms.
9. Front legs with more pronounced forward curve than back curve of back legs.
10. All legs square-sectioned, unstretchered.
Likely restoration and repair
11. Caned seats replaced with upholstery, covering front seat rail.
12. Legs broken, split and
pinned - most vulnerable point just below knees of front legs. Examine grain closely for
repairs.
13. Back supports broken and repaired. Both these points may not detract from appearance but considerably weaken structure.
14. Decorative brass rosettes on sides of knees, seat frame
junction with back legs - may conceal pinning or repair.
15. Attractive if incongruous carving on front legs other than reeding. Probably conceals a partly replaced leg.
commercial proposition. Its lines derive from Ancient Greek and Egyptian rather than the Adam `classical’ and it represented the height of the Regency taste for unbroken lines and severe curves. Probably the most well-known design – certainly the most copied and reproduced – is the `Trafalgar’ chair, with a rope-twist incorporated into the crest rail or back rail, made to commemorate Nelson’s victory.
There had been many technical advances in furni making by the end of the eighteenth century. Steam-driven machinery, bonding, laminating and veneer-cutting , all had a considerable influ on furniture design. There also a far greater scientific understanding of weight and stress. The flush-sided chair remarkably modern construction, with the timbers cut scientifically across the grain so that the leg and side-frame were made in a single piece, bonded to the curving back and back leg in a single continuous line.
Construction and materials
This radical design was made in solid mahogany, rosewood, simulated rosewood, ebonized beech, real and simulated calamander, and, in some less costly versions, with side frames and seat rails of solid dark woods with a beech underframe. The test of a genuine flush-sided chair is that it can be laid completely flat on its side on the floor. Legs are always unstretchered, the front legs frequently have a more pronounced curve than the back legs - hence its name ’sabre leg’. The crest rail, often several inches deep, is tenoned to the inside of the back supports and does not overrun the seat frame. Chairs with flush sides and crest rails over-running the side are of later date. Seats were upholstered and curved with the side-frame. They were never overstuffed at the front, where there was always a straight seat rail joining the two high-curving knees.
In line with the fashions of the day, the sabre-legged chair was also made in a lighter construction, with a dark wood, or ebonized beech for the frame, and caned seat and back panel.
Detail
Frequently there was continuous reeding which carried from the side of the crest rail, down the top of the seat frame, over the knees and down the front of the slightly tapered square-sectioned legs. Brass inlay, stringing and decoration were flush with the surface. On arms, there is often scrolling at the end of the armrest.
Variations
These chairs required a considerable amount of technical knowledge and equipment to make, and consequently there are no country versions of this design.
The simple shape of the traditional slat back with a deep, plain crest rail and plain wooden or rush seat could probably be related to the sabre-legged chair, but it would be stretching the point. The most commonly reproduced design is the over-curving S-armed chair with matching
dining chairs, often with caned seats, and most frequently found in beechwood, ebonized or painted and gilded. Strictly speaking, these are not true flush-sided chairs, since their arms are round-sectioned and their wide crest rails usually overrun the sides.
Below left: flush-framed, c.1830. Right: cane-seated, flush-framed, c.1820. The rope-twist crest rail has been broken by a stylized decorative design.
Reproductions
Victorian
From the beginning of the Victorian period, the pure shape of the flush-sided chair became spoiled by turned front legs instead of the strict curve of the sabre leg. This was probably because the flush-sided chair was by nature expensive to make and used a considerable amount of timber to achieve the right
spring and strength to the legs.
Twentieth century
Few of the myriad variations begin to match the elegance and simplicity of the original. About 30 years ago the lyre back was very much in fashion, and a variation of the flush-sided chair was made commercially by some high-quality manufacturers, usually in ebonized beech. They proved to be far less durable than the originals, mainly because the difficult cross-cutting of the timber was skimped, and the sabre legs split where the grain ran at too acute an angle.
Modern versions of a cane-seated flush-sided chair are to be found in some high-quality department stores, made with modern techniques, probably in High Wycombe, centre of the chair-making industry in
England, where many of the originals were also made.
Price bands
Late Regency, with overrunning crest rail, £120-150 each. Set of six, £800-1,000.
Cane seat, simulated rosewood, beach frame - set of six, £.880-1,000.
S-arm chair, £250-320.
Plain mahogany - set of six, £700-900.
(Rosewood more expensive than mahogany; brass inlay also more expensive.)
William iv turned leg - set of six, £600-850.